Cartell DriveGuard Integrator™

Wireless With Linear

Wireless With Linear

Cartell and Linear partner to offer a remote vehicle detection system. Except for a small amount of direct burial cable attached to a sensor probe, you can easily have a wireless solution.

SYSTEM REQUIREMENTS

1. Cartell CP-1TT-12V system (includes sensor probe and small output board)
2. Cartell CF-2C or CT-2B control unit; or CT-8 annunciator
3. Linear XT-1 Transmitter with Linear ANT-2 Antenna
4. Linear XR-1 Receiver with Linear ANT-1 Antenna
5. 12 Volt battery to power the CP-1 output board. Solar panel may also be considered (7 AMP/hour) to charge battery
6. A second 12 Volt battery in the home (can use Linear’s T-124.8DC power supply)
7. Weatherproof plastic box
8. 500 – 1000 Ω, 1/4 watt resistor

INSTRUCTIONS – SENSOR PROBE, OUTPUT BOARD, BATTERY AND TRANSMITTER

See Figure 1.Linear 1

Install the CP-1 probe beside a 12 foot wide driveway

See Figure 1.

Install the following in a weatherprooLinear 2f box:

  • CP-1 output board
  • 12 volt battery
  • Linear XT-1 Transmitter with Linear ANT-2 Antenna

See Figure 2.

Hook the CP-1 probe, 12 volt battery and Linear XT-1 Transmitter to CP-1 output board as seen in Figure 2.

INSTRUCTIONS – INTEGRATING DIRECTLY WITH AA-1 AUDIBLE DEVICE

See Figure 3.

Linear 31. Install a Linear XR-1 Receiver with a Linear ANT-1 Antenna in the home.
2. Install a 12 volt D.C. power source near the Receiver.
3. Connect positive power to Common contact of Receiver.
4. Connect negative power to annunciator’s GND (Ground) terminal.
5. Connect Receiver’s Normally Open contact to annunciator’s SON (Sonalert) terminal.

INSTRUCTIONS – INTEGRATING WITH CF-2C OR CT-2B CONTROL UNITS

See Figure 4.

Linear 41. Install a Linear XR-1 Receiver with a Linear ANT-1 Antenna in the home.
2. Install either a CT-2B (sound only) or CF-2C (sound and lights) control unit in the home near the Receiver.
3. Connect 12 volt D.C. power source to the Receiver (suggested Linear power supply is T-124.8DC, wall mounted).
4. Connect Receiver’s N.O. contact to terminal #10 on CT-2B or terminal #17 on CF-2C.
5. Connect Receiver’s Common contact to terminal #12 on CT-2B or terminal #19 on CF-2C.
6. In the place of the Cartell sensor probe, place a 500 -1000 ohm 1/4 watt resistor across terminals #10 & #12 on the CT-2B or across terminals #17 & #19 on the CF-2C.

Print Version

Wireless With Inovonics

Wireless With Inovonics

Cartell and Inovonics partner to offer a remote vehicle detection system. Except for a small amount of direct burial cable attached to a sensor probe, you can easily have a wireless solution.

SYSTEM REQUIREMENTS

1. Cartell CP-1TT-9V system (includes sensor probe and small output board)
2. Cartell CF-2C or CT-2B control unit; or CT-8 annunciator
3. Inovonics FA210 Analog Universal Transmitter. Note: this has been replaced with the digital version EN1210. Or choose the Inovonics FA250 Analog High Power Universal Transmitter, which has been replaced with the digital version EN1210W.
4. Inovonics FA401R Analog Receiver (has been replaced with EN4204R digital receiver)
5. 9 volt Alkaline or Lithium battery to power CP-1 output board
6. 12 volt battery to power Receiver in the home
7. Weatherproof plastic box
8. 500 – 1000 Ω, 1/4 watt resistor

INSTRUCTIONS – SENSOR PROBE, OUTPUT BOARD, BATTERY AND TRANSMITTER

Inovonics 11. See Figure 1.
Install the CP-1 probe beside a 12 foot wide driveway

2. See Figure 1.
Install the following in a weatherproof box:

  • CP-1 output board
  • Inovonics 29 volt Alkaline or Lithium battery
  • Inovonics Transmitter Model FA210 for shorter ranges or FA250 for longer ranges (which have been replaced with EN1210 or EN1210W respectively).

3. See Figure 2.
Hook the CP-1 probe, 9 volt battery and Inovonics Transmitter to CP-1 output board as seen in Figure 2.

4. On the CP-1 output board, turn the relay time potentiometer fully clockwise for maximum relay time.

INSTRUCTIONS – INTEGRATING DIRECTLY WITH AA-1 AUDIBLE DEVICE

See Figure 3.

Inovonics 3

1. Install a single channel Receiver in the home (Inovonics FA401R (new product number is EN4204R)).

2. Install a 12 volt D.C. power source near the Receiver

3. Connect positive power to Common contact of Receiver.

4. Connect negative power to annunciator’s GND (Ground) terminal.

5. Connect Receiver’s Normally Open contact to annunciator’s SON (Sonalert) terminal.

INSTRUCTIONS – INTEGRATING WITH CF-2C OR CT-2B CONTROL UNITS

See Figure 4.

1. InInovonics 4stall a single channel Receiver in the home (Inovonics FA401R (new product number is EN4204R)).

2. Install either a CT-2B (sound only) or CF-2C (sound and lights) control unit in the home near the Receiver.

3. Connect 12 volt D.C. power source to the Receiver.

4. Connect Receiver’s N.O. contact to terminal #10 on CT-2B or terminal #17 on CF-2C.

5. Connect Receiver’s Common contact to terminal #12 on CT-2B or terminal #19 on CF-2C.

6. In the place of the Cartell sensor probe, place a 500 -1000 ohm 1/4 watt resistor across terminals #10 & #12 on the CT-2B or across terminals #17 & #19 on the CF-2C.

Print Version

Integrating With Other Systems

Integrating With Other Systems

Cartell easily integrates with any home automation, security or lighting system, offering to those systems the protection and convenience of professional vehicle detection. This is because our control units have floating, dry relay contacts.

SYSTEM REQUIREMENTS

One (1) CT-2B control unit
One (1) CT-6 sensor probe

INSTRUCTIONS

You will need two things to have a successful installation:

The manual for your home automation, security or lighting panel
A resistor
(consult your manual for the correct size)

See Figure 1.
 CT-2B control unit  and CT-6 sensor probeHook the CT-2B to two zone inputs on your panel. If your system’s contacts are normally closed, use terminals 5 & 6 on the CT-2B. At your system’s panel, place a resistor between the terminals in parallel (see your H.A. manual for resistor size).

If your H.A. contacts are normally open, use terminals 6 & 7 on the CT-2B and place a resistor between the terminals in series (see your H.A. manual for resistor size).

Note: Use the power supply that came with the CT-2B to power it rather than relying on the home automation or security panel for power.

FURTHER INSTRUCTIONS FROM HAI

The following instructions were written by the technicians at Home Automation, Inc.:
1. Connect the Power supply that came with the CT-2B to terminals 1 and 2 on the Cartell CT-2B control unit.
2. Connect either the NC and C or the NO and C terminals of the Cartell CT-2B control unit to a zone on the HAI board. Install a resistor according to the terminals connected to. If NC and C were used, the resistor should be in series. If NO and C were used, the resistor should be in parallel.
3. On the HAI system, select the proper zone type for the Driveway Sensor. The zone types can be found under Setup>>Installer>>Zones. NOTE: Unless this is to be used for security purposes, the zone type should be set to Auxiliary (Type 64).

SAMPLE AUTOMATION PROGRAMS

The first program example will turn on the outdoor lighting for 20 minutes when the driveway sensor is tripped at night.
WHEN Driveway NOT READY
AND IF DARK
THEN Outdoor Lights ON FOR 20 MINUTES
The next programming example will change the view on a touchscreen to the proper camera when the driveway sensor is tripped.
WHEN Driveway NOT READY
THEN SHOW CAMERA 1 ON TOUCHSCREEN 1

Print Version

Using Other Sensing Devices

Using Other Sensing Devices

Are you tired of having to jerry-rig sensors in order to give clients a full-featured detection system? Now you can enjoy a fully-functioning, professional detection system, using many sensing devices of your choice.

Cartell’s control units are engineered to accept other sensing devices in conjunction with— or exclusive of—the CT-6 sensor probe. You may use a combination of sensors and sensor types on one system.*

Here’s how…

SYSTEM REQUIREMENTS

1. A Cartell CT-2B or CF-2C control unit.
2. A sensing device with a normally open, floating, dry relay contact
3. A 500 – 1000 Ω, 1/4 watt resistor

INSTRUCTIONS

1. Install the Cartell control unit as outlined in the manual that came with your system.

2. See Figure 1.
Sensing DevicesConnect one side of the sensing device contact to terminal #10 on the CT-2B or terminal #17 on the CF-2C.

3. Connect the other side of the sensing device contact to terminal #12 on the CT-2B or terminal #19 on the CF-2C.

4. In the place of the Cartell sensor probe, place a 500 -1000 ohm 1/4 watt resistor across terminals #10 & #12 on the CT-2B or across terminals #17 & #19 on the CF-2C.

Now when your sensing devices are tripped, Cartell will trigger all the functions supported by the control unit.

* Sensors may include inductive loop, motion, microwave, passive infrared, photoelectric eye, reflective beam, and our own CT-6 sensor probe, etc.

Print Version

DriveGuard Integrator™ (CT-2B System)

DriveGuard Integrator™ (CT-2B System)

The DriveGuard Integrator™ system (product code: CT-2B system) adds professional car detection
to any security, home automation or lighting system.

Integrator When connected to two zone inputs on a security or home automation panel, the DriveGuard Integrator™ will trigger any and all features supported by those systems when vehicles are detected.

Its sensor is buried beside and near the end of the driveway, hidden and vandal-proof. It only detects moving steel, eliminating false alarms caused by animals or blowing objects. Its control unit is installed beside the security or home automation panel.

When integrating vehicle detection with a home automation or security system, the following will be enabled when vehicles drive into the driveway:

  • Turn on lights at night
  • Chime at keypads
  • Play audible recordings at keypads (“Car is in the driveway,” etc.)
  • Post messages at keypads
  • Pull up driveway cameras on screen
  • Notify external sources (police, etc.)
  • Cooperate with computer modules to interact with computers, email, etc.

This system is recommended for driveways longer than 75 feet.

American made and supported.

DriveGuard Integrator™ Features

  • Based on magnetometer technology
  • Provides trigger and relay output for seamless integration with any security, home automation or lighting system
  • Sensor probe buried beside and near the end of the driveway, hidden and vandal-proof
  • Covers 12 foot wide driveway
  • Direct burial cable of sensor coated with polyurethane and spliceable for field repairs
  • Supports any sensing device with a N.O., dry, floating relay contact
  • Single zone system
  • Single timed output
  • Supports up to 4 sensor probes
  • Manual trip test button
  • Adjustable sensor sensitivity
  • Adjustable relay time
  • Re-trigger hold-off
  • Transient suppression built in
  • RFI/EMF protection
  • Directional when using two systems together
  • Includes 12 volt transformer
  • Five year warranty
  • Made and supported in the U.S.

DriveGuard Integrator™ Components

Two components make up the DriveGuard Integrator™ system:

1. CT-2B control unit (includes 12 volt transformer)

2. CT-6 sensor probe

Component description:

CT-2B CT-2B control unit

The CT-2B control unit has a single timed output with simplified features. Field adjustments include relay time and sensor probe sensitivity.

It comes in a high quality, white metal enclosure and is usually installed beside the home automation, security or lighting panel for easy integration with those systems.

The CT-2B supports up to four sensor probes.

NOTE: Use the power supply that comes with the CT-2B to power it rather than relying on the home automation or security panel for power.

• CT-6 sensor probe

Sensor Probe Based on magnetometer technology, the CT-6 detects movement in the earth’s magnetic field caused by moving steel. It will not detect animals, people or blowing objects. Wind and weather do not affect it. This makes it virtually false-alarm proof. It does not require power.

The CT-6 sensor probe should be buried 6-10 inches underground, toward the end, beside, and parallel to, the driveway. It covers a 12′ wide driveway from the side. Wider driveways will require more than one sensor probe. It has direct burial cable attached, making conduit unnecessary. The cable is buried 3-6 inches underground, up to and into the house. It is connected to the control unit.

The CT-6 comes with a custom length of direct burial cable attached in increments of 50′ from 100′ to 500′; comes in increments of 100′ from 500′ to 3000′. The cable is polyurethane coated, making repair-splicing in the field possible.

DriveGuard Integrator™ Technical Specs

Integrator Tech Specs

Print Version