Cartell Remote System

Wireless With Linear

Wireless With Linear

Cartell and Linear partner to offer a remote vehicle detection system. Except for a small amount of direct burial cable attached to a sensor probe, you can easily have a wireless solution.

SYSTEM REQUIREMENTS

1. Cartell CP-1TT-12V system (includes sensor probe and small output board)
2. Cartell CF-2C or CT-2B control unit; or CT-8 annunciator
3. Linear XT-1 Transmitter with Linear ANT-2 Antenna
4. Linear XR-1 Receiver with Linear ANT-1 Antenna
5. 12 Volt battery to power the CP-1 output board. Solar panel may also be considered (7 AMP/hour) to charge battery
6. A second 12 Volt battery in the home (can use Linear’s T-124.8DC power supply)
7. Weatherproof plastic box
8. 500 – 1000 Ω, 1/4 watt resistor

INSTRUCTIONS – SENSOR PROBE, OUTPUT BOARD, BATTERY AND TRANSMITTER

See Figure 1.Linear 1

Install the CP-1 probe beside a 12 foot wide driveway

See Figure 1.

Install the following in a weatherprooLinear 2f box:

  • CP-1 output board
  • 12 volt battery
  • Linear XT-1 Transmitter with Linear ANT-2 Antenna

See Figure 2.

Hook the CP-1 probe, 12 volt battery and Linear XT-1 Transmitter to CP-1 output board as seen in Figure 2.

INSTRUCTIONS – INTEGRATING DIRECTLY WITH AA-1 AUDIBLE DEVICE

See Figure 3.

Linear 31. Install a Linear XR-1 Receiver with a Linear ANT-1 Antenna in the home.
2. Install a 12 volt D.C. power source near the Receiver.
3. Connect positive power to Common contact of Receiver.
4. Connect negative power to annunciator’s GND (Ground) terminal.
5. Connect Receiver’s Normally Open contact to annunciator’s SON (Sonalert) terminal.

INSTRUCTIONS – INTEGRATING WITH CF-2C OR CT-2B CONTROL UNITS

See Figure 4.

Linear 41. Install a Linear XR-1 Receiver with a Linear ANT-1 Antenna in the home.
2. Install either a CT-2B (sound only) or CF-2C (sound and lights) control unit in the home near the Receiver.
3. Connect 12 volt D.C. power source to the Receiver (suggested Linear power supply is T-124.8DC, wall mounted).
4. Connect Receiver’s N.O. contact to terminal #10 on CT-2B or terminal #17 on CF-2C.
5. Connect Receiver’s Common contact to terminal #12 on CT-2B or terminal #19 on CF-2C.
6. In the place of the Cartell sensor probe, place a 500 -1000 ohm 1/4 watt resistor across terminals #10 & #12 on the CT-2B or across terminals #17 & #19 on the CF-2C.

Print Version

Wireless With Inovonics

Wireless With Inovonics

Cartell and Inovonics partner to offer a remote vehicle detection system. Except for a small amount of direct burial cable attached to a sensor probe, you can easily have a wireless solution.

SYSTEM REQUIREMENTS

1. Cartell CP-1TT-9V system (includes sensor probe and small output board)
2. Cartell CF-2C or CT-2B control unit; or CT-8 annunciator
3. Inovonics FA210 Analog Universal Transmitter. Note: this has been replaced with the digital version EN1210. Or choose the Inovonics FA250 Analog High Power Universal Transmitter, which has been replaced with the digital version EN1210W.
4. Inovonics FA401R Analog Receiver (has been replaced with EN4204R digital receiver)
5. 9 volt Alkaline or Lithium battery to power CP-1 output board
6. 12 volt battery to power Receiver in the home
7. Weatherproof plastic box
8. 500 – 1000 Ω, 1/4 watt resistor

INSTRUCTIONS – SENSOR PROBE, OUTPUT BOARD, BATTERY AND TRANSMITTER

Inovonics 11. See Figure 1.
Install the CP-1 probe beside a 12 foot wide driveway

2. See Figure 1.
Install the following in a weatherproof box:

  • CP-1 output board
  • Inovonics 29 volt Alkaline or Lithium battery
  • Inovonics Transmitter Model FA210 for shorter ranges or FA250 for longer ranges (which have been replaced with EN1210 or EN1210W respectively).

3. See Figure 2.
Hook the CP-1 probe, 9 volt battery and Inovonics Transmitter to CP-1 output board as seen in Figure 2.

4. On the CP-1 output board, turn the relay time potentiometer fully clockwise for maximum relay time.

INSTRUCTIONS – INTEGRATING DIRECTLY WITH AA-1 AUDIBLE DEVICE

See Figure 3.

Inovonics 3

1. Install a single channel Receiver in the home (Inovonics FA401R (new product number is EN4204R)).

2. Install a 12 volt D.C. power source near the Receiver

3. Connect positive power to Common contact of Receiver.

4. Connect negative power to annunciator’s GND (Ground) terminal.

5. Connect Receiver’s Normally Open contact to annunciator’s SON (Sonalert) terminal.

INSTRUCTIONS – INTEGRATING WITH CF-2C OR CT-2B CONTROL UNITS

See Figure 4.

1. InInovonics 4stall a single channel Receiver in the home (Inovonics FA401R (new product number is EN4204R)).

2. Install either a CT-2B (sound only) or CF-2C (sound and lights) control unit in the home near the Receiver.

3. Connect 12 volt D.C. power source to the Receiver.

4. Connect Receiver’s N.O. contact to terminal #10 on CT-2B or terminal #17 on CF-2C.

5. Connect Receiver’s Common contact to terminal #12 on CT-2B or terminal #19 on CF-2C.

6. In the place of the Cartell sensor probe, place a 500 -1000 ohm 1/4 watt resistor across terminals #10 & #12 on the CT-2B or across terminals #17 & #19 on the CF-2C.

Print Version

Remote System (CP-1TT System)

Remote System (CP-1TT System)

The Remote vehicle detection system (product code: CP-1TT) is used to trigger RF and Satellite transmitters for interface with wireless applications when vehicles are detected.

Two models are availRemote Detection Probeable: 9 volt and 12 volt. Most of the sensitive electronics are located in the sensor probe, leaving a small 2½ square inch external circuit board conformal coated for installation in an outdoor, weatherproof box.

Its sensor is buried beside a driveway or lane, hidden and vandal-proof. It only detects moving steel, eliminating false alarms caused by animals or blowing objects.

With relay time and probe sensitivity adjustments and the choice of N.O. and N.C. dry relay contacts, this is one of the most versatile and dependable remote vehicle detection systems available in the market today.

This product has been used successfully for over twenty years. Both the United States and Canadian governments rely on it in their homeland security, border patrol and forestry services.

American made and supported.

Remote System Features

  • Based on magnetometer technology
  • Sensor buried beside driveway, hidden and vandal-proof
  • Covers 12 foot wide driveway
  • Direct burial cable of sensor coated with polyurethane and spliceable for field repairs
  • Single zone system
  • Triggers most any RF and Satellite transmitter
  • Excellent for use with solar power
  • Two systems: 9 volt & 12 volt
  • Small circuit board for mounting in outdoor, weatherproof box
  • Under 60 micro-amps standby current
  • N.O. and N.C. relay contacts
  • Manual trip test button for diagnostic purposes
  • Transient suppression against lightning built in
  • RFI/EMF protection
  • Adjustable sensor sensitivity
  • Adjustable relay time
  • Five year warranty
  • Made and supported in the U.S.

Remote System Components

Five components are necessary to make up the Remote System:

1. CP-1 Sensor probe

2. CB-1TT output board (9 volt & 12 volt models)

3. Transmitter of your choice

4. Receiver of your choice

5. Outdoor, weatherproof box of your choice

Component description:

CP-1 Probe • CP-1 Sensor probe

Based on magnetometer technology, the CP-1 sensor probe detects movement in the earth’s magnetic field caused by moving steel. It will not detect animals, people or blowing objects. Wind and weather do not affect it. This makes it virtually false-alarm proof. Most of the sensitive electronics are located in this probe.

Typically, the CP-1 sensor probe should be buried 6-10 inches below ground, beside, and parallel to, the driveway or lane. It covers a 12′ wide driveway from the side. It has direct burial cable attached, making conduit unnecessary. The cable should be buried 3-6 inches underground, up to and into a weatherproof box that contains the output board.

The CP-1 sensor comes with 80′ of direct burial cable attached. The cable is polyurethane coated, making repair-splicing in the field possible.

CB-1 • CB-1TT output board

Two models of this board are available: 9 volt and 12 volt. It is a 2½ square inch board that should be installed in an outdoor, weatherproof box.

The CP-1TT output board has relay time and probe sensitivity adjustments and the choice of normally open and normally closed dry relay contacts.

• Transmitter and Receiver of your choice

These products are not supplied by Cartell, but we suggest you consider using Inovonics, Linear or a compatible product.

• Outdoor, weatherproof box

This product is not provided by Cartell. The weatherproof box should be attached above ground to a post, tree or sturdy object. Contents installed inside should include the CB-1TT output board, battery (9 volt or 12 volt), transmitter and receiver.

Remote System Technical Specs

Remote Tech Specs

Print Version